Afx RIS224SNMV Manuel d'utilisateur télécharger pdf

RIS Series Fluorescent Wall Sconce Fixture

Model 124 & 224

Page 1 of 1 8060559 rev.0

Safety Precautions

Read all safety precautions and installation instructions carefully

before installing or servicing this fixture. Failure to comply with

these instructions could result in potentially fatal electric shock

and/or property damage.

It is recommended that a qualified electrician perform all wiring. This

fixture must be wired in accordance with all national and local

electrical codes.

Do not handle any energized fixture or attempt to energize any

fixture with wet hands or while standing on a wet or damp surface or

in water.

This fixture is designed for use in a 120-277VAC, 60Hz fused circuit.

Do not use on a dimming circuit.

To reduce the risk of electrical shock, and to assure proper operation,

this fixture must be adequately grounded. To accomplish proper

grounding, there must be a separate ground wire (green) or bare metal

contact (metal conduit) between this fixture and the ground

connection of your main power supply panel. The green ground

screw location is clearly marked on the fixture housing.

This fixture is intended for general indoor lighting in dry or damp

locations only.

Assembly Instructions

1. Preparing for installation

A. Disconnect electrical power before installing or servicing any part of

this fixture.

B. Carefully remove glass diffuser(s) (1) from separate packaging.

C. Remove back plate (5) from main housing (3) by removing top and

bottom screws (4).

2. Wiring

All wiring must take place inside junction box.

Caution: Make sure power is off at fuse or circuit breaker box. Check power

wires for damage or scrapes. If power supply wires are within 3 inches of ballast

use wire suitable for at least 90

C (194

F). Note: Most dwellings built before

1985 have supply wire rated to 60

C. Consult a qualified electrician before

installing.

A. This unit will not operate properly unless connected to a “grounded”

electrical circuit. Electrical shock, overheating, low or no light output,

and shortened lamp life can result if proper grounding is not done.

Securely attach green (or green and yellow) wire to green

B. Connect the white supply wire to the white ballast lead. Connect black

supply wire to black ballast lead. Do not mix wires. Pull on each wire

lead to make sure connections are secure. Make certain no bare wires

are exposed outside of wire connectors.

3. Fixture mounting

A. Mount back plate (5) to junction box using the 2 mounting screws (6)

provided in the parts bag.

B. Position the main housing (3) over the back plate (5). Align holes and

secure using the provided screws (4).

4. Diffuser installation

A. Install 24W 2G11 base lamp(s) (2) by inserting pins into lamp holder(s) located in the main housing (3) and pressing until

lamp snaps in place.

B. Install diffuser(s) (1) by rotating them clockwise into main housing (3) until they are securely fastened

C. Restore power at fuse or circuit box.

Limited Factory Warranty

American Fluorescent Corporation warrants this fixture is free from defects in materials and workmanship when installed and used under normal operating conditions

for a period of 2 years from date of purchase. This warranty covers all component parts and extends only to replacement of defective fixture or components; it does not

cover failure due to improper installation, misuse, mishandling or damage incurred in transit.

Safety Precautions 1

Résumé du contenu

Page 1 - Safety Precautions

RIS Series Fluorescent Wall Sconce Fixture Model 124 & 224

Modèles reliés RIS124SNMV

Commentaires sur ces manuels

Pas de commentaire

Afx RIS224SNMV Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Éclairage Afx RIS224SNMV. AFX RIS224SNMV User Manual Manuel d'utilisatio

Résumé du contenu

Modèles reliés RIS124SNMV

Commentaires sur ces manuels

Produits connexes et manuels pour Éclairage Afx RIS224SNMV