Afx SHS1218218QMVACLN Manuel d'utilisateur télécharger pdf

Limited Factory Warranty

American Fluorescent Corporation hereby warranty that this fixture is free from defects in materials and workmanship when installed and used under normal operating conditions for a period

of 2 years from date of purchase. This warranty covers all component parts and extends only to replacement of defective fixture or components; it does not cover failure due to improper

installation, misuse, mishandling or damage incurred in transit.

SHS Series Fluorescent Wall Sconce

Models 113, 118, 213, 218

Page 1 of 1 8060274 Rev 4

Safety Precautions

Read all safety precautions and installation instructions carefully

before installing or servicing this fixture. Failure to comply with

these instructions could result in potentially fatal electric shock

and/or property damage.

It is recommended that a qualified electrician perform all wiring. This

fixture must be wired in accordance with all national and local

electrical codes.

Do not handle any energized fixture or attempt to energize any

fixture with wet hands or while standing on a wet or damp surface or

in water.

This fixture is designed for use in a 120-277VAC, 60Hz. Do not use

on a dimming circuit.

To reduce the risk of electrical shock, and to assure proper operation,

this fixture must be adequately grounded. To accomplish proper

grounding, there must be a separate ground wire (green) or bare metal

contact (metal conduit) between this fixture and the ground

connection of your main power supply panel. The green ground

screw location is clearly marked on the fixture housing.

This fixture is intended for use for general indoor lighting in dry or

damp locations only.

Assembly Instructions

1. Preparing for installation-

A. Disconnect electrical power before installing or servicing any part of this

fixture.

B. Remove shade assembly (1), cast arm(s) (2) and backpan assembly (5) from

cartons. Separate contents of hardware bag.

C. Attach cast arm(s) to backpan assembly by inserting threaded stem (4) of cast

arm(s) through hole(s) in bottom lens bracket(s). Secure firmly with locknut(s).

Note: single sconce shown.

2. Wiring- all wiring must take place inside junction box.

Caution: Make sure power is off at fuse or circuit breaker box. Check power wires for

damage or scrapes. If power supply wires are within three inches of ballast use wire

suitable for at least 90C (194F). Note: Most dwellings built before 1985 have supply wire

rated to 60C. Consult a qualified electrician before installing.

A. Attach gem bar (7) to junction box (not provided) with two of the long screws

provided.

B. Securely attach green (or green and yellow) wire to bare wire from junction box.

C. Using luminaire disconnect (provided), insert white supply wire into the hole

across from white

ballast lead. Insert

black hot supply

wire into hole across from black ballast lead. Do not mix wires. Pull on each

wire to make sure connections are secure. Make certain no bare wires are

exposed outside of luminaire disconnect.

D. Tuck all connections neatly into junction box.

3. Mounting-

A. Adjust threaded stem (6) in gem bar so that approx. 1-1/4” is exposed and

tighten with locknut. Either use fixture as a template for mounting tab(s) (3)

positioning OR measure 12-1/2” from center of stem and mark for backplate

mounting hole. (Double sconce mounting tab (3) center-to-center level

distance is 6-1/2”). Drill 3/16” pilot hole.

B. Attach mounting tab (3) (s) to wall with anchor(s) and long screw(s) provided.

C. Place bottom of fixture arm(s) (2) onto tab backplate(s) (3) and swing up and

over stem. Secure with thumbscrew (9).

D. Install wood screw (A) into anti-rotational hole (B) in back pan to prevent the

fixture from rotating. (FIGURE TO LEFT)

4. Lamp -Install appropriate lamp(s) (not provided) per label on face of backpan.

Insert lamp pins into lamp holder and press downwards until lamp snaps in place.

5. Shade -To install the shade assembly, align the two holes in the diffuser with the two holes on the top of the backpan and secure with short

screws (8).

6. Restore power at fuse or circuit breaker box.

Fluorescent Wall Sconce 1

Résumé du contenu

Page 1 - Fluorescent Wall Sconce

Limited Factory Warranty American Fluorescent Corporation hereby warranty that this fixture is free from defects in materials and workmanship when ins

Commentaires sur ces manuels

Pas de commentaire

Afx SHS1218218QMVACLN Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Éclairage Afx SHS1218218QMVACLN. AFX SHS1218218QMVACLN User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Éclairage Afx SHS1218218QMVACLN