Afx TYS11231400L30D2SNLA Manuel d'utilisateur télécharger pdf

TYS Series LED Wall Sconce Fixture

Models TYS1123

Page 1 of 1 8060762 R0

Safety Precautions

Read all safety precautions and installation instructions carefully

before installing or servicing this fixture. Failure to comply with

these instructions could result in potentially fatal electric shock

and/or property damage.

It is recommended that a qualified electrician perform all wiring. This

fixture must be wired in accordance with all national and local

electrical codes.

Do not handle any energized fixture or attempt to energize any

fixture with wet hands or while standing on a wet or damp surface or

in water.

Make sure that the power source conforms to the requirements of the

fixture (see labels on fixture housing).

To reduce the risk of electrical shock, and to assure proper operation,

this fixture must be adequately grounded. To accomplish proper

grounding, there must be a separate ground wire (green) or bare metal

contact (metal conduit) between this fixture and the ground

connection of your main power supply panel. The green ground

screw location is clearly marked on the fixture housing.

This fixture is intended for use for general indoor lighting in dry or

damp locations only.

Assembly Instructions

1. Preparing for installation-

A. Disconnect electrical power before installing or servicing any part of this

fixture.

B. Remove shade assembly (1), cast arm assembly (4) and back pan assembly (7)

from cartons. Separate contents of hardware bag.

2. Arm Assembly-

A. Assemble lower cast arm assembly (4) using provided screw (5)

B. Install lower diffuser (13) over cast arm assembly (4) before assembling upper

cast arm assembly (10) using provided hardware.

C. Attach and align the cast arm assembly (4) with the back pan (7) and secure

with the provided nipples and hex nuts.

3. Wiring- all wiring must take place inside junction box.

Caution: Make sure power is off at fuse or circuit breaker box. Check power wires for

damage or scrapes. If power supply wires are within three inches of driver use wire

suitable for at least 90C (194F). Note: Most dwellings built before 1985 have supply

wire rated to 60C. Consult a qualified electrician before installing.

A. This unit will not operate properly unless connected to a “grounded” electrical

circuit. Electrical shock, overheating, low or no light output, and shortened

lamp life can result if proper grounding is not done. Securely attach green (or green and yellow) wire to back of fixture with

provided hardware.

B. Using wire nuts (provided), connect white (common) supply wire to white fixture lead. Connect black (hot) supply wire to

black fixture lead. Do not mix wires. Pull on each wire lead to make sure connections are secure. Make certain no bare wires

are exposed outside of wire connectors. Note: fixtures with universal voltage power supplies are pre-wired

with a disconnect. Refer to the included guide for using the disconnect

4. Mounting-

A. Adjust threaded stem (11) in gem bar (12) so that approx. 1-3/8” is exposed and tighten with locknut. Either

use fixture as a template for mounting bracket plate (9) positioning OR measure 18” from center of threaded

stem (11) to the bottom of the mounting bracket plate (9) and mark for bracket plate mounting hole. Drill

1/8” pilot hole.

B. Attach mounting bracket plate (9) to wall with anchor(s) (if required) and ¾” screw(s) (8) provided.

C. Place the lower arm assembly plate (4) onto mounting bracket plate (9) and swing up and over stem (11). Secure with

thumbnut (3) and secure the lower cover plate with the screw (6) provided.

D. Install wood screw (A) into anti-rotational hole on back pan to prevent the fixture from rotating. (See Fig 2)

5. Shade-

A. To install the shade assembly (1), align the two holes on the diffuser with the two holes on the top of the back pan (7) and

secure with short screws (2).

B. Restore power at fuse or circuit breaker box.

Limited Factory Warranty

AFX Inc. hereby warranty that this fixture is free from defects in materials and workmanship when installed and used under normal operating conditions for a period of

5 years from date of shipment from factory. This warranty covers all component parts and extends only to replacement of defective fixture or components; it does not

cover failure due to improper installation, misuse, mishandling or damage incurred in transit.

Fig 2

LED Wall Sconce Fixture 1

Résumé du contenu

Page 1 - LED Wall Sconce Fixture

TYS Series LED Wall Sconce Fixture Models TYS1123 Page 1 of 1

Commentaires sur ces manuels

Pas de commentaire

Afx TYS11231400L30D2SNLA Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Éclairage Afx TYS11231400L30D2SNLA. AFX TYS11231400L30D2SNLA User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Éclairage Afx TYS11231400L30D2SNLA