Models:
1 of 2
Read all safety precautions and installation instructions carefully before
installing or servicing
this fixture. Failure to comply with these
instructions could result in potentially fatal electric shock and/or
property damage.
It is re
commended that a qualified
fixture must be wired in accordance with all national and local
electrical codes.
Do not handle any energized fixture or attempt to energize any fixture
with wet hands or while standing on a
ASSEMBLY
1.
Preparing for installation
A.
Disconnect electrical power
fixture.
B.
Carefully remove the fixture from the carton, and check that all parts are included,
below. Be careful not to misplace any of the screws or parts which are needed for installing the fixture.
2. Wiring-
all wiring must take place inside
junction box.
Caution:
Make sure power is off at fuse or circuit
breaker box. Ch
eck power wires for damage or
scrapes. If the
power supply wires are within three
inches of the ballast
for at least 90C (194F).
Note:
Most dwellings built before 1985 have supply
wire rated to 60C. Consult a qualified ele
before installing.
A. Loosen screws (3)
and remove gem bar
clockwise.
B.
Install gem bar on the juncti
with two screws (2)
C. Make all wires
Secure with wire nuts
D.
power source to the green screw
E.
The black wire from the fixture is connected to the
black wire from power source.
F. The white wire from
the fixture is connected to the
white (neutral) wire from power source.
G.
Tuck all connections neatly into junction box.
Read all safety precautions and installation instructions carefully before
this fixture. Failure to comply with these
instructions could result in potentially fatal electric shock and/or
commended that a qualified
electrician perform all wiring. This
fixture must be wired in accordance with all national and local
Do not handle any energized fixture or attempt to energize any fixture
with wet hands or while standing on a
wet or damp surface or in water.
Preparing for installation
Disconnect electrical power
at fuse or circuit breaker box before installing or servicing any part of this
Carefully remove the fixture from the carton, and check that all parts are included,
below. Be careful not to misplace any of the screws or parts which are needed for installing the fixture.
all wiring must take place inside
Make sure power is off at fuse or circuit
eck power wires for damage or
power supply wires are within three
, use wire suitable
Most dwellings built before 1985 have supply
wire rated to 60C. Consult a qualified ele
ctrician
-installed on the gem bar (1)
it counter
Install gem bar on the juncti
on box by securing it
.
to the appropriate wire.
).
s from the fixture and
power source to the green screw
in the gem bar.
The black wire from the fixture is connected to the
black wire from power source.
the fixture is connected to the
white (neutral) wire from power source.
Tuck all connections neatly into junction box.
120VAC / 60Hz
This fixture is designed for use in a 110
Do not use on a dimming circuit.
To reduce the risk of electrical shock, and to assure proper operation,
this fixture must be adequately grounded. To
grounding, there must be a separate ground wire (green)
between
this fixture and the ground connection of your main power
supply panel.
This fixture is intended to be used for general
locations.
at fuse or circuit breaker box before installing or servicing any part of this
Carefully remove the fixture from the carton, and check that all parts are included,
below. Be careful not to misplace any of the screws or parts which are needed for installing the fixture.
8060743 R0
120VAC, 60Hz fused circuit.
To reduce the risk of electrical shock, and to assure proper operation,
this fixture must be adequately grounded. To
accomplish proper
grounding, there must be a separate ground wire (green)
contact
this fixture and the ground connection of your main power
This fixture is intended to be used for general
indoor lighting in damp
at fuse or circuit breaker box before installing or servicing any part of this
below. Be careful not to misplace any of the screws or parts which are needed for installing the fixture.
Commentaires sur ces manuels