BBS Series Fluorescent Wall Sconce Fixture
Model 213
Page 1 of 1 8060095 rev.1
Safety Precautions
Read all safety precautions and installation instructions carefully
before installing or servicing this fixture. Failure to comply with
these instructions could result in potentially fatal electric shock
and/or property damage.
It is recommended that a qualified electrician perform all wiring. This
fixture must be wired in accordance with all national and local
electrical codes.
Do not handle any energized fixture or attempt to energize any
fixture with wet hands or while standing on a wet or damp surface or
in water.
This fixture is designed for use in a 110-120VAC, 60Hz fused circuit.
Do not use on a dimming circuit.
To reduce the risk of electrical shock, and to assure proper operation,
this fixture must be adequately grounded. To accomplish proper
grounding, there must be a separate ground wire (green) or bare metal
contact (metal conduit) between this fixture and the ground
connection of your main power supply panel.
This fixture is intended to be used for general indoor lighting in dry
or damp locations only.
Assembly Instructions
1. Preparing for installation
A. Disconnect electrical power before installing or servicing any part of this
fixture.
B. Remove fixture; place the frame (7) and the bag with hardware off to the
side.
2. Wiring.
All wiring must take place inside junction box.
Caution: Make sure power is off at fuse or circuit breaker box. Check power wires
for damage or scrapes. If power supply wires are within three inches of ballast use
wire suitable for at least 90C (194F). Note: Most dwellings built before 1985 have
supply wire rated to 60C. Consult a qualified electrician before installing.
A. This unit will not operate properly unless connected to a “grounded”
electrical circuit. Electrical shock, over heating, low or no light output, and
shortened lamp life can result if proper grounding is not done. Securely
attach green (or green and yellow) wire to back of fixture with provided
hardware.
B. Using wire connectors (provided), connect white supply wire to white ballast
lead. Connect black hot supply wire to black ballast lead. Do not mix wires. Pull on each wire lead to make sure connections
are secure. Make certain no bare wires are exposed outside of wire connectors.
3. Fixture mounting.
A. Back pan mounting options
1. Gem Bar Mounting – Secure gem bar (4) (provided) to junction box (not supplied) with #8-32 x 1” screws (provided).
Install 2” stem (5)(provided) into the gem bar. Use the lock nut to secure stem at the proper length. Install Back pan (2)
over stem and secured in place with knob (3). (Note: Adjust length of stem to create secure fit.)
2. Secure to junction box – Holes supplied in back pan (2) enable direct mounting to junction box (not supplied).
3. Secure to Wall – Holes supplied in back pan (2) enable direct wall mounting (hardware not supplied).
4. Install appropriate lamps (1) (not supplied) by inserting lamp pins into lamp holder and press until lamp snaps in place.
4. Frame installation
A. To install the frame (1), remove frame screws from back pan at location (6). Align frame (7) above back pan (2), Slide
diffuser down over back pan (2). Secure with 2 mounting screws (8) provided.
B. Restore power at fuse or circuit breaker box.
Limited Factory Warranty
American Fluorescent Corporation hereby warranty that this fixture is free from defects in materials and workmanship when installed and used under normal operating
conditions for a period of 2 years from date of shipment from factory. This warranty covers all component parts and extends only to replacement of defective fixture or
components; it does not cover failure due to improper installation, misuse, mishandling or damage incurred in transit.
(1 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels