Afx HZP620SNSCTD Manuel d'utilisateur télécharger pdf

HZP Series Fluorescent Pendant

Models 413/613

Page 1 of 2 8060464 Rev. 8

*MV model shown with 4-

in CFL’s

Safety Precautions

Read all safety precautions and installation instructions carefully

before installing or servicing this fixture. Failure to comply with

these instructions could result in potentially fatal electric shock

and/or property damage.

It is recommended that a qualified electrician perform all wiring. This

fixture must be wired in accordance with all national and local

electrical codes.

Do not handle any energized fixture or attempt to energize any

fixture with wet hands or while standing on a wet or damp surface or

in water.

Make sure that the power source conforms to the requirements of the

fixture. (See labels on fixture housing).

Models ending in MV power source 120-277V Non-dimmable

Models ending in SCTD power source 120V (Self Ballasted

dimmable CFL) Usable on a dimming circuit with dimmable lamps

To reduce the risk of electrical shock, and to assure proper operation,

this fixture must be adequately grounded. To accomplish proper

grounding there must be a separate ground wire (green) or bare metal

contact (metal conduit) between this fixture and the ground

connection of your main power supply panel.

This fixture is intended for use as general lighting in dry or damp

locations.

Assembly Instructions

1. Preparing for installation.

A. Disconnect electrical power before installing or servicing any part of this fixture.

B. Unpack and lay out all fixture components to verify everything is included to fully assemble the fixture.

C. Please affix all stems with supplied thread locker to prevent stems from coming undone when assembled.

2. Fixture assembly - Lighting fixture is partially assembled

A. Take the fixture power wires (black and white) and feed them

through the 1-½” stem assembly (10). Thread the stem assembly

into the fitting on top of the ballast/lamp tray until secure.

B. Slide diffuser support (11-only found on 6-lamp unit) over 1

½” stem assembly and allow it to rest on top of the ballast/lamp

mounting tray. NOTE: Verify Step 2C is completed prior to

moving on for the 6-lamp unit only.

C. Feed wires through the ½” nipple (8B) and stem (9) and screw

the stem into nipple on top of the 1-½” stem (10).

NOTE: Two 6” and two 12” stems included for

desired height between 1-½” stem and canopy.

D. Slide wires through ½” threaded nipple (8A) and screw nipple

¼” into stem (9) and swivel assembly (6). Slide wires through

swivel (6) and canopy (5) assembly and tighten.

3. Fixture mounting.

A. Install short screws (2) provided into threaded holes near ends

of gem bar (3). Be sure these screws line up with holes in

canopy.

B. Insert 1 ½” (4) screws through slots in gem bar (3) and

secure to junction box in ceiling (not provided). Be sure short

screws (2) in gem bar (3) pointing down. Slide supply wires

through center hole of mounting bracket.

4. Wiring.

Caution: Make sure power is off at fuse or circuit breaker box. Check

power wires for damage or scrapes. If power supply wires are within

three inches of ballast use wire suitable for at least 90C (194F). Note:

Most dwellings built before 1985 have supply wire rated to 60C.

Consult a qualified electrician before installing.

1 2

Résumé du contenu

Page 1 - Safety Precautions

HZP Series Fluorescent Pendant Models 413/613 Page 1 of 2

Page 2

HZP Series Fluorescent Pendant Models 413/ 613 Page 2 of 2

Modèles reliés HZP413SNMV

Commentaires sur ces manuels

Pas de commentaire

Afx HZP620SNSCTD Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Éclairage Afx HZP620SNSCTD. AFX HZP620SNSCTD User Manual Manuel d'utilisatio

Résumé du contenu

Modèles reliés HZP413SNMV

Commentaires sur ces manuels

Produits connexes et manuels pour Éclairage Afx HZP620SNSCTD