Afx DYP418SNMV Manuel d'utilisateur télécharger pdf

DYP Series Fluorescent Pendants

Models 418MV / 420SCTD / 618MV/ 620SCTD

Page 1 of 2 8060533 Rev. 3

FIG 3

Safety Precautions

Read all safety precautions and installation instructions carefully

before installing or servicing this fixture. Failure to comply with

these instructions could result in potentially fatal electric shock

and/or property damage.

It is recommended that a qualified electrician perform all wiring. This

fixture must be wired in accordance with all national and local

electrical codes.

Do not handle any energized fixture or attempt to energize any

fixture with wet hands or while standing on a wet or damp surface or

in water.

Make sure that the power source conforms to the requirements of the

fixture. (See labels on fixture housing).

Models ending in MV, can be supplied with 120-277VAC. These

units are NOT DIMMABLE.

Models ending in SCTD, must be powered with 120VAC ONLY.

The units can be used with an approved dimmer. (Call American

Fluorescent Customer Service for dimming information) When

dimming: Only Use CFSB20K27D from American Fluorescent.

6 lamps MAXIMUM per dimmer switch.

To reduce the risk of electrical shock, and to assure proper operation,

this fixture must be adequately grounded. To accomplish proper

grounding there must be a separate ground wire (green) or bare metal

contact (metal conduit) between this fixture and the ground

connection of your main power supply panel.

This fixture is intended for use as general lighting in dry or damp

locations.

Assembly Instructions

1. Preparing for installation.

A. Disconnect electrical power before installing or servicing any part of this fixture.

B. Unpack and lay out all fixture components to verify everything is included to fully assemble the

fixture.

C. Please affix all aircraft cables with supplied connector adapters to prevent cables from coming

undone when assembled.

2. Fixture assembly - Lighting fixture is partially assembled

A. Lamp Shade / 11” Pan with Cord / Cable Assembly:

 Remove the hex nut and lock washer from the 11” pan stem

assembly (do not remove the 1-1/8” flat washer).

 Now, feed the cord through the center hole of the shade assembly

and mechanically secure it with the hex nut and lock washer that

you removed before.

 Feed through the three cable (11) to the connectors that are mounted

on the 11” pan. Insert the cable by pressing the “Spring Pin”

(12)(A) Fig 5 downward and holding until it comes out at the other

end. Repeat these steps for the other cables. Note: Cable length

adjustments might be needed again for the correct cord length

alignment.

B. Take the fixture power cord wires (Fig 3) and slide them through the

canopy (6) strain relief assembly (8).

Cord Length Adjustments / Cutting / Stripping Wire Ends:

 Before cutting the cord, measure the desired cord length for pendant

mounting. Tighten the strain relief by threading tapered metal finial

to mechanically secure the cord.

 For wiring NEC (National Electrical Code) requirements, cut the

cord about 7” from the canopy (6) as shown in Fig 3.

 Cut the cord outside jacket insulation about 3” from canopy (6) and then stripped 3/8” the

ends of the three wires (13) same as shown in Fig 3.

3. Fixture mounting from Junction Box (Fig 1).

A. Install the short screws (1) with lock washers (3) and hex nuts (4) all provided into the offset

holes (2) of the round mounting bracket as shown in Fig 1. Be sure these two screws (1) line up

with holes in canopy (6) and point away from junction box.

Note: These short screws (1) may require adjustment to mount the two ball nuts (7)

correctly.

FIG 2

FIG 1

1 2

Résumé du contenu

Page 1 - Safety Precautions

DYP Series Fluorescent Pendants Models 418MV / 420SCTD / 618MV/ 620SCTD Page 1 of 2

Page 2

DYP Series Fluorescent Pendants Models 418MV / 420SCTD / 618MV/ 620SCTD Page 2 of 2

Modèles reliés DYP620SNSCTD

Commentaires sur ces manuels

Pas de commentaire

Afx DYP418SNMV Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Éclairage Afx DYP418SNMV. AFX DYP418SNMV User Manual Manuel d'utilisatio

Résumé du contenu

Modèles reliés DYP620SNSCTD

Commentaires sur ces manuels

Produits connexes et manuels pour Éclairage Afx DYP418SNMV