Afx AEL232RBMV Manuel d'utilisateur télécharger pdf

AEL SERIES Aeon

Models 232/432 Ceiling Mounted Fixture

Safety Precautions

Read all safety precautions and installation instructions carefully

before installing or servicing this fixture. Failure to comply with

these instructions could result in potentially fatal electric shock

and/or property damage.

It is recommended that a qualified electrician perform all wiring. This

fixture must be wired in accordance with all national and local

electrical codes.

Do not handle any energized fixture or attempt to energize any

fixture with wet hands or while standing on a wet or damp surface or

in water.

Model numbers ending in MV are designed for use in a 120-

277VAC, 60Hz fused circuit; otherwise the fixture is designed for

use in a 110-120VAC, 60Hz fused circuit. Do not use on a dimming

circuit unless unit is provided with appropriate dimming ballast.

To reduce the risk of electrical shock, and to assure proper operation,

this fixture must be adequately grounded. To accomplish proper

grounding, there must be a separate ground wire (green) or bare metal

contact (metal conduit) between this fixture and the ground

connection of your main power supply panel. The green ground

screw location is clearly marked on the fixture housing.

This fixture is intended to be used for dry, indoor lighting locations.

Parts Inventory (Items to be Assembled)

Packed inside the carton:

1) 1 Channel Sub-assembly with socket/bracket sub-assembly (Cut the plastic tie wraps on the flat carton)

Note: Same as Fig 2

2) Two swivel sub-assembly (See Fig 1)

a) 1 swivel sub-assembly with wires (A), assembled to plate (5)

b) 1 swivel sub-assembly without wires (B), assembled to plate (5)

3) Plate (5), Canopy (11), 2 stems (13) included, each stem has 2 Flat washer (14), (15), 1 lock washer, 1 hex nut

4) Parts bag: Small wire connectors, 2 #8-32 x 1inch long (4), 2 #8 lock washer (8), 2 #8-32 hex nut (9)

5) One 4ft metal frame with diffuser (25) (See Fig 5)

Assembly Instructions

1. Preparing for installation

A. Consult a local licensed electrician or electrical

contractor about installing the fixture if you are not sure

about installation.

2. Select a suitable dry location (use for indoors only). Make

sure mounting surface is capable of supporting the 19lbs

weight of the fixture.

3. Installing Fixture Mounting Plate (Fig 1) (Fixture

Total Load Weight: 19 lbs)

A. Before installing the mounting plate (5) that is shown in

Fig 1, make sure the two #8 screws (4), two lock

washers (8) and two hex nuts are installed to the

plate (5), and also make sure that the wires (19) and

ground wire (7) are placed under the plate (5) and

the end wires are able to reach the wiring location

area. Install the plate on the outlet box. Note: To rigidly

secure the plate, it is recommended to use an outlet box

and extra support hardware ¼ trade size screws (not

included) or ¼ toggle bolts (not included) at the four ¼

diameter hole located at both ends of the plate (5).

4. To Install Canopy / Stem to Plate Assembly (Fig 1)

A. Align the 2 holes on the canopy to the plate

two #8-32x1inch (4) and use the ball nut

(11) to secure the canopy temporarily.

B. Feed through the wires (19) to the stem (14)

and thread the end of the stem to the nipple

that is attached on the swivel bracket

assembly (A). Repeat these procedures to

connect the other stem (without wires) to the

swivel bracket assembly (B). Note: When

tightening the stem to the threads of the nipple from swivel bracket

assembly (a) and (b) make sure that the swivel ball groove is locked in

place to the bracket tab.

5. Assembling Channel Fixture (Use Fig 1 to Fig 4)

A. First remove hardware flat washers (15), (16), lock washers (17), hex nuts

(18) on both of the stems and also remove the channel cover (2) by using

the procedure in Fig 3.

Note: When mounting channel assembly, make sure that the ballast is near

the stem that has the wires.

B. Install the channel assembly: first make sure that you have the flat washers (15) installed on both of the stems (will be on top

of the channel after installation). Feed the wires through the channel hole (near ballast side) and align the other stem with the

other hole on the channel as they are shown in Fig 1 and Fig 2. Now re-install the hardware that you took off temporarily,

while holding the channel with one hand, fasten the flat washer (16), lock washer (17) and mechanically secure the channel

with the hex nut (18).

Tools Required: Phillips Screwdriver, Adjustable Wrench & Pliers.

Hardware Required: Appropriate mounting hardware

8060146 R2

1 of 2

1 2

Résumé du contenu

Page 1 - Assembly Instructions

AEL SERIES Aeon Models 232/432

Page 2 - Ceiling Mounted Fixture

AEL SERIES Aeon Models 232/432

Modèles reliés AEL432SAMV

Commentaires sur ces manuels

Pas de commentaire

Afx AEL232RBMV Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Éclairage Afx AEL232RBMV. AFX AEL232RBMV User Manual Manuel d'utilisatio

Résumé du contenu

Modèles reliés AEL432SAMV

Commentaires sur ces manuels

Produits connexes et manuels pour Éclairage Afx AEL232RBMV