Afx CAL432SNMV Manuel d'utilisateur télécharger pdf

Chase Linear Ceiling Mounted Fluorescent Fixture

CAL432

Page 1 of 1 8060554 rev.1

Limited Factory Warranty

American Fluorescent Corporation warrants this fixture is free from defects in materials and workmanship when installed and used under normal operating conditions

for a period of 2 years from date of purchase. This warranty covers all component parts and extends only to replacement of defective fixture or components; it does not

cover failure due to improper installation, misuse, mishandling or damage incurred in transit.

FIGURE 1

FIGURE 4

FIGURE 2

FIGURE 3

Safety Precautions

Read all safety precautions and installation instructions carefully

before installing or servicing this fixture. Failure to comply with

these instructions could result in potentially fatal electric shock

and/or property damage.

It is recommended that a qualified electrician perform all wiring. This

fixture must be wired in accordance with all national and local

electrical codes.

Do not handle any energized fixture or attempt to energize any

fixture with wet hands or while standing on a wet or damp surface or

in water.

This fixture is designed for use in a 110-120VAC, 60Hz fused circuit.

Do not use on a dimming circuit.

To reduce the risk of electrical shock, and to assure proper operation,

this fixture must be adequately grounded. To accomplish proper

grounding, there must be a separate ground wire (green) or bare metal

contact (metal conduit) between this fixture and the ground

connection of your main power supply panel. The green ground

screw location is clearly marked on the fixture housing.

This fixture is intended for general indoor lighting in dry or damp

locations only.

Assembly Instructions

1. Preparing for installation.

A. Disconnect electrical power before installing or servicing this fixture.

B. Remove channel cover (2) by squeezing at each end in the fixture channel (1). Remove

appropriate knockout(s) for power supply entry. To remove knockouts it is

recommended to use a blunt object facing away from you to punch out.

2. Channel mounting.

A. Position the fixture channel (1) onto the ceiling and mark all appropriate mounting

locations. You may need someone to help you hold the fixture up. Take the fixture

channel (1) down and punch a small hole in the ceiling at each of the locations you

have marked using a nail or stud finder to see if there is a wood joist above that you

can mount the fixture to. Where there is a wood joist, use a suitable wood screw (not

included) to mount the fixture. Where there is no joist to screw into, a 3/16” toggle

bolt (not included) must be used to mount the fixture channel securely to the ceiling.

3. Wiring.

Caution: Make sure power is off at fuse or circuit breaker box. Check power wires for damage or scrapes.

If power supply wires are within three inches of ballast use wire suitable for at least 90C (194F). Note:

Most dwellings built before 1985 have supply wire rated to 60C. Consult a qualified electrician before

installing. This unit will not operate properly unless connected to a “grounded” electrical circuit. Electrical

shock, overheating, low or no light output, and shortened lamp life can result if proper grounding is not

done. Feed the green (or green and yellow) wire through knockout and securely attach to provided green

ground screw.

A. Feed the white and black wires through knockout. Using wire nuts (not provided);

connect white supply wire to white ballast lead. Connect black hot supply wire to black

ballast lead. Pull on each wire lead to make sure connections is secure. Make certain no

bare wires are exposed outside of wire nuts.

B. Replace ballast cover (2) by placing one edge of ballast cover into dimples, swing upward,

and press cover allowing second edge to catch second set of dimples and lock in place.

Make sure no wires become crimped between cover and fixture.

4. Lamping

A. Install appropriate lamps (F32T8 - not included) by aligning the lamp to the proper lamp

holder. Insert linear lamp pins into lamp holders and rotate into place to seat lamp for

proper connection. Repeat until all lamps are installed.

5. Diffuser Assembly and Installation.

A. (Figure 2) Assemble the decorative brackets (5) onto the lower diffuser (4) with provided

screws (7) on both ends. Attach the decorative end plate (9) and end diffuser (8) to decorative

bracket (5) with provided screws on both ends.

B. (Figure 3) Hook end with flange to fixture channel; (Figure 4) swing opposite end up and

mount decorative bracket (5) to fixture channel (1) with provided screw (10). Repeat to secure

opposite end with flange to fixture channel (1).

C. Restore power at fuse or circuit breaker box.

Résumé du contenu

Page 1 - Assembly Instructions

Chase Linear Ceiling Mounted Fluorescent Fixture CAL432 Page 1 of 1

Commentaires sur ces manuels

Pas de commentaire

Afx CAL432SNMV Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Éclairage Afx CAL432SNMV. AFX CAL432SNMV User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Éclairage Afx CAL432SNMV