Model: 326928
1 of 1
Limited Factory Warranty
AFX Lighting, Inc.
warrants this fixture is free from defects in materials and workmanship when installed and used under
period of 3
years from date of purchase. This warranty covers all component parts and extends only to replacement of defective fixture or
not cover failure due to improper installation, misuse, mishandl
Read all safety precautions and installation instructions carefully before
installing or servicing this fixture. Failure to comply with these
instructions could result in potentially fatal electric shock and/or
property damage.
It is re
commended that a qualified
fixture must be wired in accordance with all national and local
electrical codes.
Do not handle any energized fixture or attempt to energize any fixture
with wet hands or while standing on a
1.
Preparing for installation
A. Disconnect electrical power
at fuse or circuit breaker box before installing or servicing any part of this fixture.
B.
Carefully remove the fixture from the carton, and check that all parts a
of the screws or parts which are needed for installing the fixture.
A. Assemble 5 glass panels
B.
Place diffuser (2) on the frame bottom;
C. Place four diffusers (3) on
secure the glass panels.
2. Wiring-
all wiring must take place inside junction box.
Caution:
Make sure power is off at fuse or circuit breaker box. Check power wires for damage
or scrapes. If power supply wires
are within three inches of
suitable for at least 90C (194F).
to 60C. Consult a qualified electrician before installing.
D. Secure gem bar (4) on the
F. Make all wire connections
to appropriate wire. Secure
G. Connect the green wires
from the fixture and power source to the green screw on the gem bar
(4).
H. The black wire from
the fixture is connected to the black wire from power source.
I.
The white wire from the fixture is connected to the white (neutral) wire from power source.
G.
Tuck all connections neatly into junction box.
3. Mounting
A. Thread nut (7) on stem (6
is exposed.
Secure the necessary length with nut (7).
B. Install two longer screws (13) (supplied) on the backpanel and secure
(9) (supplied).
B. Install back panel (8)
4. Place the frame (11) over two (
5
. Restore power at fuse or circuit breaker box.
warrants this fixture is free from defects in materials and workmanship when installed and used under
years from date of purchase. This warranty covers all component parts and extends only to replacement of defective fixture or
not cover failure due to improper installation, misuse, mishandl
ing or damage incurred in transit
Read all safety precautions and installation instructions carefully before
installing or servicing this fixture. Failure to comply with these
instructions could result in potentially fatal electric shock and/or
commended that a qualified
electrician perform all wiring. This
fixture must be wired in accordance with all national and local
Do not handle any energized fixture or attempt to energize any fixture
with wet hands or while standing on a
wet or damp surface or in water.
Preparing for installation
at fuse or circuit breaker box before installing or servicing any part of this fixture.
Carefully remove the fixture from the carton, and check that all parts a
re included, as shown in figure below. Be careful not to misplace any
of the screws or parts which are needed for installing the fixture.
metal frame (1):
Place diffuser (2) on the frame bottom;
Fold four metal tabs to
all wiring must take place inside junction box.
Make sure power is off at fuse or circuit breaker box. Check power wires for damage
are within three inches of
the ballast
Most dwellings built before 1985 have supply wire rated
to 60C. Consult a qualified electrician before installing.
x (not supplied) with two screws (5)
to appropriate wire. Secure
with wire nuts
from the fixture and power source to the green screw on the gem bar
the fixture is connected to the black wire from power source.
The white wire from the fixture is connected to the white (neutral) wire from power source.
Tuck all connections neatly into junction box.
ust the length of the stem
in the gem bar so that approx. 3/8”
Secure the necessary length with nut (7).
B. Install two longer screws (13) (supplied) on the backpanel and secure
6) and secure it with the thumbnut (10).
) backpan screws and secure it
. Restore power at fuse or circuit breaker box.
warrants this fixture is free from defects in materials and workmanship when installed and used under
normal operating conditions for a
years from date of purchase. This warranty covers all component parts and extends only to replacement of defective fixture or
ing or damage incurred in transit
This fixture is designed for use in a 110
Do not use on a dimming circuit.
To reduce the risk of electrical shock, and to assure proper operation,
this fixture must be adequately grounded. To
grounding, there must be a separate ground wire (green)
between
this fixture and the ground connection of your main power
supply panel.
This fixture is intended to be used for general
damp locations only.
at fuse or circuit breaker box before installing or servicing any part of this fixture.
re included, as shown in figure below. Be careful not to misplace any
Make sure power is off at fuse or circuit breaker box. Check power wires for damage
, use wire
Most dwellings built before 1985 have supply wire rated
ed)
).
from the fixture and power source to the green screw on the gem bar
the fixture is connected to the black wire from power source.
The white wire from the fixture is connected to the white (neutral) wire from power source.
in the gem bar so that approx. 3/8”
with the two nuts
2).
120VAC / 60Hz
8060664 R4
normal operating conditions for a
years from date of purchase. This warranty covers all component parts and extends only to replacement of defective fixture or
components; it does
120VAC, 60Hz fused circuit.
To reduce the risk of electrical shock, and to assure proper operation,
this fixture must be adequately grounded. To
accomplish proper
grounding, there must be a separate ground wire (green)
contact
this fixture and the ground connection of your main power
This fixture is intended to be used for general
outdoor lighting in dry or
re included, as shown in figure below. Be careful not to misplace any
Commentaires sur ces manuels